İçeriğe geç
3 ürüne %10 indirim — sepette otomatikKargo fiyata dahil — tüm TürkiyeSiparişe özel üretim — 2–4 iş günü içinde kargodaHavale/EFT ya da kartla ödeme
FORMVIVA
0
Papatya Sabunluk
Papatya Sabunluk
Papatya Sabunluk
Papatya Sabunluk
1 / 4
Ev & Yaşam

Papatya Sabunluk

199 ₺ Kargo dahil

Papatya biçiminde bir sabunluk: yapraklar kenarı oluşturur, sabun yivli ortaya oturur, sarı göbek ayrı renktedir. Tabanında süzgeç deliği yoktur; ıslak sabundan gelen su yivlerde birikir, seramik bir sabunluk gibi ara ara boşaltıp kurutun. Sıcak havlu kurutucusunun üzerine koymayın.

3 ürüne %10 indirim — sepette otomatik uygulanır.
Renk Fotoğraftaki renkler (çok renkli)
Bu ürün hakkında soru sor
  • Siparişe özel üretim2–4 iş günü içinde kargoda
  • Kargo fiyata dahilTürkiye'nin her yerine
  • 14 gün iadeKoşulsuz cayma hakkı
  • Güvenli ödemeHavale/EFT ya da kart
Ürün bilgileri
  • Ölçü: 110 mm çap, 12,5 mm yükseklik
  • 2 renk: tabak ve göbek
  • Süzgeç deliği yok
  • Ağırlık: 46 g
  • FDM 3D baskı · PLA ya da PETG
Üretim ve teslimat

Ürününüz ödeme onayından sonra atölyemizde basılır, temizlenir ve kontrol edilir; 2–4 iş günü içinde kargoya verilir. Kargo ücreti fiyata dahildir. 3D baskı yüzeyinde ince katman çizgileri görülmesi doğaldır.

İade ve değişim

Teslimden itibaren 14 gün içinde iade edebilirsiniz. Hasarlı gelen ürünü ücretsiz yeniden basıp göndeririz. Ayrıntılar

Tasarım notları (İngilizce)

A daisy that holds a bar of soap. The petals form the rim, the ribbed centre gives the soap something to sit on, and the yellow middle is a separate part so it prints in a second colour.

110 mm across and 12.5 mm tall. One plate, 3 h 15 m, about 45 g across the two filaments.

Before you print

The base is solid — there are no drain holes. Water from a wet bar collects in the ribs and stays there, so tip it out and let it dry the way you would a ceramic dish. If you want it to drain, drill a couple of 4 mm holes between the ribs after printing; the floor is thick enough to take it.

0.12 mm layers, 2 walls, 15% infill, no supports. The fine layer height is for the petal curve and the ribs — they are shallow and a coarser layer flattens them.

Colours

Two filaments: the dish and the centre. With an AMS it prints in one go. Without one, print it in a single colour and the daisy still reads — the pattern is relief, not paint. A speckled or stone-effect filament suits it better than a flat one; the photos are a white speckled PLA.

PLA is fine in a bathroom. Keep it off a heated towel rail, and it is worth knowing soap film wipes off far more easily than it does off a textured ceramic dish.

Bu tasarımı siz de satmak ister misiniz?

Ticari lisansla baskılarını kendi işletmenizde satabilirsiniz; adınıza PDF lisans belgesi. Ayrıntılar

Aynı kategoriden

Bunlar da ilginizi çekebilir

Tümü
199 ₺kargo dahil